Safety Tips To Follow When Operating a Drill Press A good rule of thumb is to keep a 2 foot perimeter of clearance around your drill press at all times Noise cancelling headphones may also be worn to minimize the sound produced by a drill press Never wear
With a drill press the operator must be protected from the rotating chuck and swarf that is produced by the drill bit Specially designed shields can be attached to the quill and used to protect this area A telescoping portion of the shield can retract as the drill bit
POWERED HAND DRILL SAFETY The following safe work practices will help you avoid injuries when using a hand drill Pre Operation Inspection and Set Up Wear safety glasses and other appropriate personal protective equipment Disconnect the plug from
2010 4 13 nbsp 0183 32 Turn Off the Drill before Changing Drill Bits After every drilling job turn off the switch and unplug the power cord Never change drill bits when the power cord is still connected to the power supply If you accidentally press the power button you could be seriously injured Also make it a point to use the safety latch when the drill is not
Self Ejecting Drill Press Chuck Keys Several sizes of drill chuck keys are available Please refer to ANSI B11 8 2001 R2012 for specific safety requirements for drill presses DXS Series Shields No Longer Available These part numbers are no longer available
2008 2 16 nbsp 0183 32 Drill Press Safety Rules Check the speed setting to see that it is correct for your work holes over 189 in should be bored at the lowest speed Only use a type of bit that is approved by the instructor Drill bits with feed screws or are excessively long should not
Drill Press Safety Drill Press Chuck key – used to tighten and loosen the chuck Must be removed every time you use it Right is tight Left is loose When drilling a small object use a Clamp or a Vice A Backer board must be placed on the drill press table when
DRILL PRESS DO NOT use this equipment unless you have been instructed in its safe use and operation and have been given permission PERSONAL PROTECTIVE EQUIPMENT Safety glasses must be worn at all times in work areas Long and loose hair must be
123 0718 013 4 GENERAL SAFETY RULES WARNING Failure to follow these rules may result in serious personal injury or death IMPORTANT Before switching the drill press on ALWAYS check the machine for the correct setting and speed as well as ensuring
Drill Press Safety Back to Table of Contents Page 1 of 2 Drill Press Safety Prior to using a drill press you must receive basic shop safety training and equipment specific training before using this tool You must wear appropriate PPE and follow all shop rules wear appropriate PPE and follow all shop rules
2020 7 19 nbsp 0183 32 Drill press could be a dangerous machine to use if you do not take care of the safety rules properly Knowing the basic know how about them and then being extra cautious with a drill press is a must Before starting your work on the drill press you may have come across a user s guide manual which would contain all the safety rules
DRILL PRESS SAFETY RULES Drill Press Safety Rules 3 Revision Date 9 Mar 17 page 1 of 1 The drill press is a versatile machine that uses a multiple cutting edged drill bit secured in a rotating chuck to bore and drill holes normally into wood stock These
DRILL PRESS 17 Oct 11 Page 4 of 10 GENERAL DRILL PRESS SAFETY RULES a Safety glasses are required to use this tool b To prevent entanglement with the chuck or bit Tie back long hair and tuck under shirt roll up long sleeves remove gloves or
DRILL PRESSES SAFETY Drill press training is required before operating this equipment SAFETY Know the controls Know how to turn the drill press on and off Wear safety glasses when operating the drill press Wearing gloves is prohibited
SAFETY RULES FOR THE DELTA 16 1 2 quot FLOOR DRILL PRESS Read carefully before operating any machines 1 Prior to or before operating this machinery ensure that the operator has been properly trained and understood the owner s operator s manual
If the drill press is in your home the same rules apply Keep the table clean of any debris and check the floor around the machine as well Check your clothing Loose fitting clothing is comfortable that is something we can all agree on When its winter a shop or
Safe Work Instructions For Drill Presses Department Facilities Management Responsible Unit Trade Services Hazards Identified Getting clothing or hair caught in moving parts burns from hot bits sharp metal edges cuttings getting in eyes being hit by item
Introduction to Drill Press Safety This material was produced under Susan Harwood grant number SH 31214 SH7 Occupational Safety and Health Administration U S Department of Labor The contents in this presentation do not necessarily reflect the views or policies of the U S Department of Labor nor does the mention of trade names commercial products or
Drill Press Safety and Operation NOTICE Rules and guidelines listed on this page are only reminders Persons must read lab safety manual machine manual and be trained by WRL Manager Safety Rules Safety glasses are required Don t wear loose
For requirements related to drill presses see the following sections of the Occupational Health and Safety Regulation and its related guidelines available on worksafebc com Section 4 3 Safe machinery and equipment Section 10 2 General requirement
Drill Press Safety Rules 1 Always wear eye protection when operating 2 All work must be clamped down 3 One person at a time on the machine 4 Remove all jewelry pull back long hair roll up long sleeves 5 Wait for the machine to stop moving before
DRILL PRESS SAFETY Safety Rules 1 Always get permission from the instructor before using the drill press 2 Safety Goggles or a Face Shield must be worn while using the drill press Check with the instructor to see if ear protection is required as well
2022 1 17 nbsp 0183 32 Drill Press Guards and Safety Shields If your drill machine comes with a drill press guard then keep it attached and use it Just keep in mind that it s never a good idea to make adjustments to the guard if the machine is turned on so always remember to turn the machine off before you make any adjustments to the guard or shield
Our present article on 10 Safety Precautions to Take When Using A Drill Press is one such compilation of the rules that we must follow while using a Drill Press Kindly go through each of them and enjoy working with the Drill Press without any kind of trouble
Identify Drill Press Understand the safety rules Describe Tooling to be use Describe Reaming a hole Describe Drilling a hole procedure Describe power feed and hand feed tapping procedure Describe Dressing the Wheel procedures
Drill Press Safety Checklist Refer to Craftex CT021N Radial Drill Press Instruction Manual for detailed operation guidelines PPE Safety Rules Wear appropriate safety classes Use a clamp or drill vise to prevent object from spinning Lubricate drill bit when
Drill Press Safety Rules Run drill at correct RPM for diameter of drill bit and material Ask shop personnel for the correct RPM Always hold work in a vise or clamp to the drill table Use a correctly ground drill bit for the material being drilled
Drill Press Safety Rules The drill press comes in a floor or bench mounted model It has a motor driven head that has a chuck that accepts bits or cutters It also has an adjustable table on which the work is mounted It is operated by pulling a rotary lever To
Drill Press Safety Rules The drill press comes in a floor or bench mounted model It has a motor driven head that has a chuck that accepts bits or cutters It also has an adjustable table on which the work is mounted It is operated by pulling a rotary lever To
2019 6 2 nbsp 0183 32 As a business owner or machinist you care about the safety of your hydraulic press operators In order to lower the occupational risks for workers you need to follow our hydraulic press safety rules and keep up with Maintenance One of the best ways of avoiding potential failure and injury is through preventative machine maintenance